DRIVE TRAIN SECTION RED PART NUMBERS INDICATE NEW PARTS 7-127 1 2 3 4 5 6 7 8 9 10 11 CONTENTS ELECTRICAL FRAME FRONT END CONTROL WHEEL ENGINE DRIVE TRAIN FUEL EXHAUST GENERAL REFERENCE • Designed to permit the use of wider than stock rear tires by converting your belt drive to an offset chain drive. • Designed for 530 size drive chain. • Can be used on 5 or 6 speed transmissions with right or left side drive. Note: 1985/Early 1994 models will require Late 1994/Later spacer 72201 (HD 33344-94) and seal 74713 (HD 12067A). OFFSET TRANSMISSION SPROCKETS FOR BIG TWIN 5 SPEED Fits Big twin 5 speed 1985/Later with fine spline drive gear A B OFFSET TRANSMISSION SPROCKET KIT FOR BIG TWIN 4 SPEED This Transmission Sprocket and Rear Sprocket Offset Spacer Kit eases the pain of installing wider rear tires. Kit includes a chrome plated rear sprocket spacer, .310” thick, and chrome mounting hardware designed for use with flange type steel rear wheel hub. When using on models with an open primary, a belt drive style transmission mainshaft bearing support must be used. When using electric start a rear belt drive style inner primary and appropriate starter motor must be used. As with any wide tire application always check all clearances. Part 75271 24 Tooth Fits Big Twin 4 speed with rear disc BELT TO CHAIN WIDE TIRE CONVERSION KIT FOR FXR AND SOFTAIL This offset 24 tooth sprocket kit was designed to convert your Big Twin 5 speed final belt drive to a 530 chain drive and allows the use of a 150/160 width rear tire on a 4” wide rim. FXR models require the use of an FXR rear sprocket and Softail models require the use of a Big Twin 4 speed 1973/1985 rear sprocket. Changes in the final drive ratio can now be easily made by changing the rear sprocket size. A .200” thick rear sprocket spacer is also included. Always verify correct clearance of all related parts. When mounting to Late 1994/Later models, use with our 74719 seal (HD 12050). See Page 7-5 for drive chain and Page 7-117 for rear sprocket. Part 75256 Fits FXR models 1985/Later, Softail 5 speed models 1986/Later Wide Tire Related 47 tooth 45 tooth 3” wide 1 5/8” wide Description Part # Part # 1/4” offset pulley kit 79901 79905 1/2” offset pulley kit 79902 79906 3/4” offset pulley kit 79903 79907 1” offset pulley kit 79904 79908 1 1/4” offset pulley kit 79909 79910 1 1/2” offset pulley kit 79911 79912 1 3/4” offset pulley kit 79914 79915 OFFSET 8MM FRONT PULLEYS FOR SOFTAIL & DYNA WIDE TIRE APPLICATION Description Part # 1/4” offset insert and mounting hardware 77333 1/2 “ offset insert and mounting hardware 77334 3/4 “ offset insert and mounting hardware 77336 1” offset insert and mounting hardware 77354 1 1/4” offset insert and mounting hardware 77430 1 1/2” offset insert and mounting hardware 77432 1 3/4” offset insert and mounting hardware 77337 3” wide 47 tooth front pulley only 77332 1 5/8” wide 45 tooth front pulley only 77425 These Front Pulley Kits are for Softail & Dyna style frames designed for wide rear tire application & BDL primary belt drives. The aluminum belt pulleys have a hard anodized finish for years of trouble free service and the removable steel inserts retain the full width spline to shaft contact for excellent power transfer. The 3” wide pulley kits are designed for 8mm open primary application and the 1 5/8” wide pulley kits are designed for 8mm closed primary application. 1 5/8” wide kit shown assembled 3” wide kit shown unassembled Complete Pulley Kits REPLACEMENT PARTS Dimensions 23 tooth 24 tooth A = .500”, B = .750” 75280 75281 A = .810”, B = 1.060” 75282 75283
RkJQdWJsaXNoZXIy MzYzNTI=